CableEye M2-Basic, 128 Test Points Includes a 128-point fixture and electronics (test cables with a maximum of 64 conductors, not expandable), CB15 board set, PC software, database of over 200 standard cables, serial interface cable for your PC’s COM port, power module, User’s Guide, one-year warranty, one-year free tech support, and one-year free software and database upgrades. Connector types on the CB15 board set include DB25 male and female (serial and parallel interface cables), DB9 male and female (serial interface and monitor cables), HD15 male and female (video cables), Centronics 36-pin male and female (printer cables), miniDIN4 and miniDIN6 (keyboard cables), and modular jack (6-position, 6-conductor for modem and telephone cables, RJ12). Substitute another board set of equivalent value if desired. TEST pushbutton and READY, MATCH, and ERROR indicators for one-button operation. Cable measurement time less than one second. Industry-standard 64-pin dual-row latch headers interface to external test fixtures. Rugged, 1/16"-thick aluminum case with scratch-proof Lexan surface for long life in an industrial environment. Calibration not required. Ready to use. CableEye M2-Basic with CB15 boards installed.

Item 811, CableEye M2, 152 Test Points Same as M2-Basic , but includes enough test points to test SCSI cables up to 68 conductors, and is expandable to over 1000 test points by connecting expansion modules. Choose 64, 128, or 152 active test points with a switch for optimum measurement time. Additional features include a remote control socket to be used for either an external footswitch or for a custom remote control to extend panel indicators, and a 10-pin Probe socket. Calibration not required. Ready to use.

Item 821, CableEye M3, 152 Test Points
Model M3 has all of the same features as Model M2, uses the same case and software, but employs a different electronic design capable of measuring resistance. With Model M3, you may set upper and lower resistance thresholds. For contact resistance, set the low threshold to as low as 0.5 ‰, and for isolation resistance, set the high threshold as high as 10 M‰. Measure embedded resistors from 100 ‰ to 999 k‰ with 1% accuracy, and with less accuracy from 0.5 ‰ to 10 M‰. Measure diodes and resistor/diode combinations, and automatically learn networks of diodes and resistors for comparison against electronic modules with similar networks. Includes Certificate of Calibration with measurement data. Calibration recommended yearly. Ready to use.

CONNECTOR BOARD SETS
The are Board Sets available for CableEye for practically any connector combination in common use - here are just a FEW examples! (and YES you can mix and match Boards from different Board Sets)

CB1 Connector Board Set for Telco and SCSI 50-pin, RJ44/45, DB15, and BNC Cables Each board includes connectors for Centronics 50-pin male and female (Telco 25-pair and SCSI-I cables), DB15 male and female (network and video cables), two RJ44/45 modular connectors (8-position, 8-conductor network and telephone cables), and two coax BNC connectors (network and video cables). Set of two boards.
CB2 Connector Board Set for IDC Flat Cables, with Shrouded Latch Headers (large sizes) Use CB2 to test flat cables with IDC wiremount sockets. This board includes dual-row headers for 60, 50, 40, 34, and 26 pins (see Item 732A below for small header sizes). One 64-position footprint is open for a User-supplied custom size. Substitute bare headers for shrouded latch headers on special order. Set of two boards.
CB3 Connector Board Set for DB37 and DB50 Cables Each board includes connectors for DB37 male and female (RS449 and other high-speed serial cables), and DB50 male and female (digital control and communications cables). These and all other Dsub connectors we use are manufactured with machined pins (not stamped pins) for long life. Set of two boards.
CB4 Connector Board Set for v.35 and DB25 Cables Each board includes connectors for v.35 male and female (all 34 pin positions loaded), and DB25 male and female. Jackscrews on the v.35 connectors are removed for rapid connect and disconnect of cables. Set of two boards.
CB5 Connector Board Set for SCSI-I, -II and -III Cables Each board includes connectors for cables that have Centronics 50-pin male (SCSI-I), mini-Centronics 50-pin male (SCSI-I, -II), miniD 50-pin male (SCSI-I), and miniD 68-pin male (SCSI-II, -III) connectors. Use a gender changer for female cables. Requires 152 test points; compatible with Model M2 (Item 811) and Model M3 (Item 821) only. Set of two boards with expander cable.